Compressed air leaving a standard rotary screw or reciprocating plant room carries condensed water, pipe scale, oil aerosol, and hydrocarbon oil vapour that must be removed in a strict physical order before reaching sensitive pneumatic equipment, product-contact nozzles, or breathing-air outlets. Under ISO 8573-1:2010, point-of-use air purity is specified across three independent contaminant classes written in formal colon notation as ISO 8573-1:2010 [A:B:C] (solid particulate, humidity/water dewpoint, and total oil), while Australian statutory workplace and clinical duties bind separately under AS/NZS 1715:2009 Appendix A for supplied-air respirators, AS 2568:2019 Incorporating Amendment 1 for medical breathing air, and AS 2896:2021 for surgical-tool pipelines.
Use this interactive P&ID workbench to map the active downstream purification train for your process, model dryer and desiccant purge electricity using the $0.27/kWh Australian commercial and industrial benchmark tariff (2025-26 FY), print a project specification sheet, or request a 1-to-1 quote from a vetted independent Australian treatment-train or air-testing specialist. Enquiries are free and you control whether any introduction goes ahead; we may receive a referral fee if you proceed with a provider (how we are paid).
1. How the P&ID treatment-train sequence prevents downstream contamination
Every stage in a compressed air purification train protects the media immediately downstream of it. Installing a dryer or activated-carbon bed without upstream liquid and aerosol protection causes rapid adsorbent fouling, high differential pressure, and silent breakthrough at point of use.
- Compressor, aftercooler, cyclone separator and wet air receiver: Cooling discharge air to within 8 to 12 °C of ambient condenses 70% to 85% of incoming atmospheric moisture. A centrifugal cyclone separator and vertical wet receiver knock out bulk liquid water and oil slugging via zero-loss level-sensing condensate drains before air reaches any filter element.
- Coarse pre-filtration (1 µm coalescing stage): Captures rust, pipe scale, liquid water mist, and coarse oil droplets ahead of the dryer. Detailed housing and element delta-P selection is covered in our compressed air filtration engineering guide.
- Drying stage (+3 °C refrigerated vs -20 °C to -70 °C desiccant): Refrigerated dryers chill air to achieve ISO 8573-1 Class 4 (≤ +3 °C pressure dewpoint) at low electrical draw, suitable for indoor ring mains above freezing. Sub-zero pipework, hygroscopic powders, instrument air, pharmaceutical contact, and breathing-air catalyst trains require twin-tower or modular desiccant adsorption dryers achieving Class 1 to 3 (-70 °C, -40 °C, or -20 °C PDP); compare purge maths in refrigerated vs desiccant dryers and convert line pressure to atmospheric frost point with our pressure dew point calculator.
- High-efficiency fine coalescing (0.01 µm aerosol stage): Tested under ISO 12500-1, a sub-micron borosilicate coalescing element strips oil aerosol down to ≤ 0.01 mg/m³ when paired with upstream pre-filtration. Ahead of a desiccant dryer, fine coalescing prevents liquid oil from coating and permanently blinding activated alumina or molecular sieve beads.
- Activated-carbon tower or cartridge (oil vapour and odour stage): Coalescing elements cannot capture gas-phase hydrocarbon oil vapour, which rises steeply once compressor discharge or dryer inlet temperatures exceed 35 °C. Activated carbon adsorbs oil vapour and objectionable odour to hold total oil (liquid, aerosol, and vapour combined) within ISO 8573-1 Class 1 (≤ 0.01 mg/m³).
- Catalytic carbon monoxide conversion and continuous alarm (breathing and medical air): Neither coalescers nor activated carbon remove carbon monoxide (CO) drawn into an outdoor intake or generated by thermal oil cracking. Hopcalite-type catalyst beds oxidise CO into CO2 only when protected by dry upstream air (typically ≤ -40 °C PDP so water vapour does not poison the catalyst), paired with a calibrated CO monitor/alarm.
- Particulate dust polish and point-of-use validation port: Dry particulate filtration immediately downstream of desiccant and carbon beds traps attrition dust so solid particles remain within Class 1 or Class 2. Corrosion-resistant aluminium or stainless steel distribution headers preserve that purity to the dedicated point-of-use sampling valve.
2. ISO 8573-1:2010 purity class reference tables (Tables 1, 2 and 3)
All concentration limits in ISO 8573-1:2010 are referenced to Clause 4 standard conditions: air temperature 20 °C, absolute pressure 1 bar (100 kPa), and relative water vapour pressure 0. Under Clause 6.1, formal specifications must state all three classes in square brackets separated by colons as ISO 8573-1:2010 [A:B:C]. Under Clause 5.2, particles larger than 5 µm are not permitted in Solid Particulate Classes 1 to 5.
Table 1: Solid particulate classes (Classes 0 to 5)
| Particulate Class [A] | 0.1 < d ≤ 0.5 µm (particles/m³) | 0.5 < d ≤ 1.0 µm (particles/m³) | 1.0 < d ≤ 5.0 µm (particles/m³) | Clause 5.2 & Test Notes |
|---|---|---|---|---|
| Class 0 | As specified by the equipment user or supplier, and more stringent than Class 1 | Written numerical ceiling and ISO 8573-4 test method mandatory | ||
| Class 1 | ≤ 20,000 | ≤ 400 | ≤ 10 | Zero particles > 5 µm permitted (Cl 5.2); laser counter per ISO 8573-4 |
| Class 2 | ≤ 400,000 | ≤ 6,000 | ≤ 100 | Zero particles > 5 µm permitted (Cl 5.2) |
| Class 3 | Not specified | ≤ 90,000 | ≤ 1,000 | Zero particles > 5 µm permitted (Cl 5.2) |
| Class 4 | Not specified | Not specified | ≤ 10,000 | Zero particles > 5 µm permitted (Cl 5.2) |
| Class 5 | Not specified | Not specified | ≤ 100,000 | Zero particles > 5 µm permitted (Cl 5.2); Classes 6, 7 & X use mass Cp (mg/m³) |
Table 2: Humidity and vapour pressure dewpoint classes (Classes 0 to 6)
| Water Class [B] | Vapour Pressure Dewpoint (PDP) | Primary Drying Stage & Engineering Application |
|---|---|---|
| Class 0 | Tighter than Class 1 (user-specified) | Ultra-dry semiconductor or specialty gas adsorption train with calibrated hygrometer |
| Class 1 | ≤ -70 °C PDP | Molecular-sieve twin-tower desiccant dryer sized for peak Australian summer inlet temperature |
| Class 2 | ≤ -40 °C PDP | Desiccant adsorption dryer (dewpoint-demand purge control recommended above 50 L/s) |
| Class 3 | ≤ -20 °C PDP | Desiccant adsorption dryer or point-of-use membrane dryer for cold-room branches |
| Class 4 | ≤ +3 °C PDP | Refrigerated compressed air dryer for general indoor plant, spray booths and non-contact packaging |
| Class 5 | ≤ +7 °C PDP | Refrigerated dryer in temperate indoor workshops |
| Class 6 | ≤ +10 °C PDP | High-dewpoint refrigerated stage; Classes 7 to 9 and X measure liquid water Cw (g/m³) |
Table 3: Total oil classes: liquid, aerosol and vapour combined (Classes 0 to 4)
| Total Oil Class [C] | Total Oil Concentration (mg/m³) | Verification & Treatment Requirement |
|---|---|---|
| Class 0 | Tighter than Class 1 (user-specified) | Must define numerical mg/m³ ceiling at point of use; compressor badge alone is insufficient |
| Class 1 | ≤ 0.01 mg/m³ | 0.01 µm fine coalescer plus activated-carbon oil-vapour stage; verify via ISO 8573-2 and ISO 8573-5 |
| Class 2 | ≤ 0.1 mg/m³ | 1 µm pre-filter plus 0.01 µm high-efficiency coalescer (add carbon if inlet exceeds 35 °C) |
| Class 3 | ≤ 1 mg/m³ | General coalescing filtration; numerically aligns with AS/NZS 1715 Appendix A oil mist ceiling |
| Class 4 | ≤ 5 mg/m³ | Coarse workshop air only (Class X applies above 5 mg/m³) |
3. Australian regulatory interface: AS/NZS 1715, AS 2568 and AS 2896
ISO 8573-1:2010 does not regulate carbon monoxide, carbon dioxide, oxygen concentration, sulphur dioxide, or oxides of nitrogen. Whenever compressed air feeds human respiration or clinical pipelines in Australia, specifications and test certificates must cite the governing Australian Standard directly rather than substituting an ISO three-digit class.
| Australian Standard | Scope | Mandatory Contaminant, Moisture & Flow Thresholds |
|---|---|---|
| AS/NZS 1715:2009 Appendix A (referenced by AS/NZS 1716:2012) |
Industrial supplied-air respirators (abrasive blasting, spray booths, confined spaces) | O2 19.5% to 22% by vol; CO ≤ 10 ppm (11 mg/m³); CO2 ≤ 800 ppm (1,400 mg/m³); oil ≤ 1 mg/m³; no objectionable odour; cylinder water ≤ 100 mg/m³ at ≥ 12 MPa (airline dry with zero condensation); ≥ 170 L/min continuous flow per respirator (gas limits at 15 °C, 100 kPa). |
| AS 2568:2019 IncAmd 1 (Cl 5 & Table 1) |
Purity of medical breathing air produced from on-site compressor systems | O2 20.4% to 21.4%; pipeline dewpoint below minimum recorded ambient or ≤ +5 °C whichever is drier; CO ≤ 5 ppm; CO2 ≤ 500 ppm; oil ≤ 0.1 mg/m³; SO2 ≤ 1 ppm; NO + NO2 ≤ 2 ppm; odourless. |
| AS 2896:2021 Cl 2.11.2 | Medical gas pipeline systems & pneumatic surgical tools | Moisture ≤ 60 ppm by volume for surgical-tool air pipelines (preventing icing and corrosion across high-speed turbine handpieces), paired with duplex medical-grade drying and filtration. |
4. Frequently asked questions
Does an ISO 8573-1 Class 0 oil-free compressor guarantee Class 1 or Class 0 air at point of use without filtration?
No. An oil-free airend eliminates crank-case or screw-injected lubricant inside the compressor, but the intake still draws ambient urban hydrocarbons, vehicle exhaust vapours, dust, and humidity. Compressing ambient air to 7 bar(g) concentrates intake oil vapour and particulates roughly eightfold, and legacy carbon-steel pipework can shed rust downstream. Achieving verified ISO 8573-1:2010 [1:2:1] or Class 0 purity at point of use still requires staged particulate filtration, drying, hydrocarbon vapour control where ambient air is contaminated, and corrosion-resistant aluminium or stainless steel piping.
Why do desiccant dryers consume more electricity than refrigerated dryers, and how much does dewpoint-demand control save?
A heatless twin-tower desiccant dryer diverts roughly 14% to 18% of dry compressed air back through the regenerating tower to strip adsorbed moisture. Because compressed air costs roughly 0.42 kW per L/s to generate, fixed-timer purge on an 80 L/s system running 4,000 hours/yr consumes around 20,160 kWh/yr ($5,443/yr at the $0.27/kWh Australian C&I benchmark), compared with ~$1,555/yr for a +3 °C refrigerated dryer. Fitting a dewpoint transmitter (dewpoint-demand switching) holds tower changeover until the bed actually approaches saturation, cutting annual purge electricity by roughly 40% to 45% under part-load or cooler winter conditions.
Can plant air purified to ISO 8573-1:2010 [1:2:1] be fed directly to supplied-air breathing respirators?
No. ISO 8573-1:2010 [1:2:1] controls solid particles, water dewpoint, and total oil, but sets zero limits on oxygen deficiency, carbon monoxide (CO), or carbon dioxide (CO2). Australian supplied-air respirators must comply with AS/NZS 1715:2009 Appendix A, which requires clean outdoor intake siting, catalytic CO conversion, continuous CO monitoring with audible/visual alarms, non-interchangeable breathing-air couplings, at least 170 L/min continuous flow per wearer, and periodic NATA-accredited air quality testing.
Where should compressed air purity validation samples be collected?
Always sample at the critical point-of-use drop (or breathing-air manifold outlet) rather than solely at the plant-room dryer discharge. Dead legs, corroded receivers, residual oil in older ring mains, and perished drop hoses routinely degrade plant-room [1:2:1] air to Class 3 or Class 4 before it reaches packaging nozzles or cleanroom tools. Point-of-use validation typically pairs ISO 8573-4 (laser particle count), ISO 8573-3 (hygrometer dewpoint), ISO 8573-2 (oil aerosol), ISO 8573-5 (oil vapour where Class 1 applies), and ISO 8573-7 (viable microbiological sampling in GMP pharma or high-care food plants).
Engineering & commercial disclosure: Calculations and P&ID schematics are indicative engineering planning aids based on ISO 8573-1:2010, AS/NZS 1715:2009, AS 2568:2019 IncAmd 1, AS 2896:2021, and the $0.27/kWh Australian C&I tariff benchmark. Site ambient conditions, inlet temperature, pressure drop, and WHS duties require site-specific verification by a qualified engineer or NATA testing laboratory. Compressed Air Solutions does not sell equipment or conduct site testing; if you request a specialist introduction and proceed, we may receive a referral fee with no cost to enquire (how we are paid).